Chinese wholesale Pcb Portable Photosensitive Dry Film - Dry Film Applied On FPC And PCB

Chinese wholesale Pcb Portable Photosensitive Dry Film - Dry Film Applied On FPC And PCB – Lucky Innovative

Short Description:

Product Detail

Product Tags

Feedback (2)

We know that we only thrive if we can easily guarantee our combined cost competiveness and high-quality advantageous at the same time for Magnetic Tool Strip , Hico Magnetic Card , Emi Copper Foil Shielding Tape , All products and solutions arrive with high quality and fantastic after-sales expert services. Market-oriented and customer-oriented are what we now have been being immediately after. Sincerely look ahead to Win-Win cooperation !

Chinese wholesale Pcb Portable Photosensitive Dry Film - Dry Film Applied On FPC And PCB – Lucky Innovative Detail:

Product Application

Applied to Printed Circuit Board and Flexible Printed Circuit Board, with the advantage of excellent performance of tending, resolution and adhesion.

Product Structure

Dry film

Product Specification

Product Code	LK-D1238 LDI Dry Film	LK-G1038 Dry Film
Thickness (μm)	38.0±2.0
Length (m)	200ｍ
Width	According to customers’ request

Product Parameters

（1）LK-D1238 LDI Dry Film

LK-D1238 LDI Dry Film is suitable for direct imaging exposure machine, with wavelength both 355nm and 405nm .

Item and Test method			Test Data
Shortest imaging time (1.0wt.% Na2CO3 water solution, 30℃) *2			25s
Wavelength (nm)			355	405
Performance after Imaging	Photosensitivity (*2×2.0)	ST=7/21 Exposure energy*3	20mJ/cm2	15mJ/cm2
	Resolution(*2×2.0)	ST=6/21	40μm	40μm
		ST=7/21	40μm	40μm
		ST=8/21	50μm	50μm
	Adhesion(*2×2.0)	ST=6/21	50μm	50μm
		ST=7/21	40μm	40μm
		ST=8/21	35μm	35μm
	【Tending Reliability】3 10 holes (6mmφ) Rate of hole breaking (2×2.0×3 times)	ST=6/21	0%	0%
		ST=7/21	0%	0%
		ST=8/21	0%	0%
Striping end time (3.0wt.%NaOH water solution, 50℃)		ST=7/21* 1 Exposure energy	50s	50s

（2）LK-G1038 Dry Film

LK-G1038 Dry Film is suitable for contacting exposure machine, with main wavelength 365nm.

Item and Test method			Test Data
Shortest imaging time (1.0wt.% Na2CO3 water solution, 30℃) *2			22s
Performance after Imaging	Photosensitivity (*2×2.0)	ST=8/21 Exposure energy*3	90mJ/cm2
	Resolution (*2×2.0)	ST=6/21	32.5μm
		ST=7/21*1	32.5μm
		ST=8/21	35μm
	Adhesion (*2×2.0)	ST=6/21	45μm
		ST=7/21	40μm
		ST=8/21	35μm
	(Tending Reliability)3 10 holes (6mmφ) Rate of hole breaking (2×2.0×3 times)	ST=6/21	0%
		ST=7/21	0%
		ST=8/21	0%
Striping end time (3.0wt.%NaOHwater solution, 50℃)		ST=7/21*1 Exposure energy	50s

(The above data is only for reference)
Note:

*1: Stouffer 21 Stage Exposure Energy Scale.
*2×2.0: Image with twice time of shortest imaging time.
*3: If focus on the Tending Reliability, it is recommended to use the exposure energy value of 7~8 stage.
*4: The above data is tested by our own equipment and instruments.

Application Process

product

Caution In Application

(1) Application : Use this film only as resist for printed circuit board-related material and other pattern formations.
(2) Pretreatment : Organic residues, stains due to insufficient dewatering and drying on the copper surface, may cause polymerization of resist and penetration of plating or etching solution.Please dry completely after water rinsing. Especially, when the moisture remain inside the through hole, it cause the tent breakage.
(3) Substrate preheating : Preheating at too high temperature for a long time may cause rust.It should be done for less than 10 min at 80℃ and for less than 3 min at 150℃. And when the substrate surface temperature prior to lamination exceeds 70℃, the film thickness on a through-hole edge may become too thin and it may cause tenting breakage.
(4) Holding after lamination and exposure : Hold with the light shield or under yellow lamp (2 meters or more distance required). The maximum holding time in the latter case (under a yellow lamp) is 4 days. Exposure should be done within 4 days after lamination.Development should be done within 3 days after exposure. Ray of non-ultraviolet white lamp has some ultraviolet rays, so hold with the light shield by black sheet under it.Keep temperature 23±2℃ and relative humidity 60±10%RH. Laminated substrates should be put in a rack one by one.
(5) Development : When temperature of developer is over 35℃, it may make resist profile worse.
(6) Stripping : Strip within one week after lamination.
(7) Waste treatment : Dry film components in developer and stripper can be coagulated by neutralization. The coagulated components can be separated from the aqueous solution by filter press method and centrifugal method. The separated aqueous solution has some COD and BOD values, so it has to be waste-disposal treated in a proper way.
(8) Film color : The color is green/blue. Though the color may gradually discolor with time, it should not influence the characteristic.

Caution On Storage

(1) When storage is done in a dark, cool, and dry place at the temperature of 5～20℃ and relative humidity of 60%RH or lower, dry film should be used within 50 days after manufacture.
(2) Keep film rolls horizontally by using of racks or support boards for storage. When they are laid vertically, sheets of dry film may slip one by one and roll-shape may be like a bamboo sprout (rolls are laid down horizontally in a package).
(3) Take out film rolls from black sheet under a yellow lamp or the same kind of safety lamp. Do not leave them under the yellow lamp for a long time. Cover film rolls by black sheet when you store them for a long time.